Code: CECT101

As Per IS: 1199, ASTM C-124, AASHO T-120

Specifications: Same as above but electrically operated, to raise and drop the table top, approx. 15 times in 15 seconds. Suitablefor operation on 230 Volts, 50 cycles, A.C. supply.

Code: CECT106

As Per IS: 5512

This is used for measuring the consistency of Pozzolanas and also cement mortar and hydrated lime. Specifications; It consists ofa machined brass table top 250+/-2.5mm. dia mounted on a rigid stand. The table top is reinforced with equally disposed ribs andallowed to conical brass mould 100mm I.D. top dia. and 50mm high.

Code: CECT111

As Per IS: 403 I, 1727.

It is used for mixing cement pastes, mortars and pozzolanas.

Specifications: The apparatus consists of an epicyclic type stainless steel paddle imparting both planetary and revolving motion, by means of gears. It has two speeds of 140+5 r.p.m and 285+10 r.p.m with planetary motions of approximately 62 r.p.m and 125 r.p.m.+ 10 r.p.m. respectively. The stand of the mixer has arrangement to raise for lower the bowl. Complete with stainless steel bowl of about six liters capacity. Suitable for operation on 230 volts, 50 cycles, single phase, A.C. Supply.

Code: CECT116

Concrete mixer Laboratory type, electrically operated. Designed to remove the burden some work of hand mixing. Uniform thoroughly mixed batches can be produced. The counter balanced drum is easy to tilt 1.1/2 to 2cu.ft.mix. The total drumvolume is however 3cu.ft. Mounted on a sturdy rubber tyred stand, and the drum is mounted for end discharge and equippedwith end towing pole. Equipped with 1/2h.p. electric motor. Suitable for operation on 220/230 volts A.C. Single phase.

Code: CECT121

This is a hand Operated Concrete Mixer and is suitable to mix 1 cuf to 1.1/2 cft material. It is mounted on two rubber tired / stand.

Code: CECT126

As Per IS: 4031-1968, IS: 1624-1960

The Autoclave is suitable for conducting accelerated soundness tests on cements of the autoclave expansion test requiring constant steam pressure with the correspondent constant pressure. It consists of a stainless steel cylinder with a weldedheat insulated voer, mounted on a sturdy supporting frame, enclosed in a heat insulated metal housing, attractively finished.The attached control unit encloses a sensitive pressure regulator and pressure gauge, power switches and pilot lights forcontrolling the electric heating units. Inside Chamber Dimensions-10.5 diameter x40.5cm height suitable for operation on 230V,50Hz, Single Phase, A.C. Supply. Supplied complete with test bar holder, special rack to hold specimens above water level inthe autoclave and in a vertical position to expose them in the same manner.

Note: Ordinary Laboratory Cement Autoclave with Mild Steel Chambers are also avaiLable.

Code: CECT131

Code: CECT136

As Per IS: 4031, 10086, ASTM C 227.

The mould is used for casting specimens of cement aggregate combinations fro measuring the potential expansive alkali reactivity.

Specifications: The mould, which has 25mm x 25mmx 250mm. effective gauge length is made of mild steel and has accurately machined faces. The parts of the moulds are tight fitting and firmly held together when assembled. Supplied complete with base

Code: CECT141

Do as above but with two compartments assembled on a angle base plate.

Code: CECT146

Do as above but three compartments.

Code: CECT151

Do as above but three compartments.Shrinkage Bar Mould (Four Gang)

Note: Bar mould as above but in gun metal as well as with knurled and threaded reference pins are also avaiLable.

Spares: Stainless steel smooth or knurled and threaded reference pins as required. Supplied in packs of one dozen.

Code: CECT156

As Per IS: 4031, 269, BS: 12.

This is for use while casting a cement briquette,

Specifications: The standard spatula consists of a steel blade, of a special shape. A wooden handle is fixed to the stem of blade.The weight does not exceed 340gms.

Code: CECT161

As Per IS: 4031, BS:12.

Specifications: Weight approximately 210gm. Best quality with hardwood handle Blade length approx. 200mm.

Code: CECT166

As Per IS: 4031 & ASTM: C 190

Specifications: 100 to 150mm long steel blade with straight edges

Code: CECT171

It is used for finding out the linear deformation caused on two reference points fixed on a loading member.

Specifications: This portable gauge is designed for a gauge length of 20c.m of the reference pins. The deformation isindicated by a 0.002 x 10mm dial gauge attached to the instruments. Complete with two standard bars for 20cm gauge lengthsupplied in a wooden case. Accessories: Reference pins in packet of 100 Nos.

Code: CECT176

This is for determining the lateral extension of 15 cm dia. x 30cm high cement concrete cylinders while testing them under compression.

Specifications: The unit consists of two movable frames pivoted at one end. The extensometer is fixed to the specimen with the help of tightening screws. The lateral extension is indicated on a dial gauge of .002mm x 12mm travel. The extension is magnified 2.5 times and the dial gauge readings are to be divided by 2.5 to get the exact read-ings. A spacer strip is provided to initially set the dial gauge, and can be removed after initial setting. Supplied in a wooden carrying case.

Code: CECT181

It is designed for finding out the deformation and strains on 15cms. Diameter and 30cms high cement concrete cylinders when subjected to compressive loads. Specifications: Consists of a frame with a bottom ring and a top ring with tighteningscrews to firmly clamp the compressometer over the cylinder. A dial gauge .002mm x 12mm is mounted on the upper ring andthe tip of the dial gauge rests on an anvil. The zero of the dial gauge can be set by adjusting the anvil screw. Supplied ina wooden carrying case.

Code: CECT186

As Per IS: 1199-1959 & 4031-1968

It is used to measure the drying shrinkage of concrete autoclave expansion of Portland cement and potential expansive reactivity of cement aggregate combinations in mortar bars during storage, on self drying. Specifications: The instrument consists ofa chanelled base over which two vertical pillars are fixed. An adjustable cross plate is at the top. A dial guage, reading to.002mm x 12 mm. can be fixed to the top cross plate. The plunger end of the dial gauge can be located upon a 6.5mm. dia. ball orother reference cemented in the specimen. On the base there is a similar recessed seating in which can be placed a second ball or reference point in the specimen. Complete with a stainless steel standardization bar with insulated grip and with 6.5mm dia. balls mounted in the ends. The unit can be supplied with a .0001inch x 1/2inch dial gauge at extra cost if indicated at the time of placing the order.

Code: CECT191

As Per IS: 4031 & BS: 1881, ASTM: C 490

The Instrument is used for determining the volume change of cement concrete. Specifications: The apparatus comprises of onemould 100mm x 100mm x 250mm, effective gauge length complete with base plate, Four reference pins, One length comparator frame, One stainless steel reference bar with insulated grip, and one dial gauge, 0.02mm x 10mm.

Code: CECT196

ASTM: C 128, AASHO: T 84

Used for determining the slumps of fine aggregate in the determination of bulk and apparent specific gravity and absorptionof fine aggregate. Specifications: The Equipments comprises of a conical metal mould 1.5inch dai. at the top, 3.5 inch dia. at the base and 2.7/8 inchin height. A metal tamping rod weighing 12 ounces and having a flat circular tamping face 1 inch in diameter.