Interface Real Time Clock
Code:EET2471
Interface ADC0809
Code:EET2476
Interface Dual DAC0800
Code:EET2481
Features:
- Supported Piggy Bag Modules:
- Code EET2481a - Piggy Bag XILINX XC9572 CPLD (optional)
- Code EET2481b - Piggy Bag XILINX XC95108 CPLD (optional)
- Code EET2481c - Piggy Bag XILINX SPARTAN XC3S50 FPGA(optional)
- Code EET2481d - Piggy Bag XILINX SPARTAN XC3S400 FPGA(optional)
- Piggy Bag ALTRA EPIC6PQ240CB FPGA(optional)
- Indicators
- 16 input using 2 nos. Of 8 way DIP Switch with LED indication to indicate logic low and logic high
- 16 LED for output indication.
- 03. Onboard Interfaces
- 4 Digit Seven Segment Displays
- 8 bit A/D convertor using ADC-0809.
- 8 bit D/A convertor using DAC-0800.
- Stepper Motor Interface.
- Relay Interface.
- Ps2 Interface.
- RS-232 Interface.
- VGA Interface.
- 16x1 Alphanumeric LCD Display.
- 5x4 Keys Keyboard Matrix.
- 04. ISP Programmer for Piggy Bag Module
- Clock generator
- On-board 50MHz, 10MHz, 5MHz, 1MHz, 100KHz & 100Hz.
- Power selection : On-board of 5V, 3.3V, 2.5V, 1.5V & 1.2V.
- Power on Reset and configuration reset key
- I/O expansions are provided through 26 pin FRC Connector for other application interface.
- All IC's are mounted on IC Sockets.
- Bare board Tested Glass Epoxy SMOBC PCB is used.
- In-Built Power Supply of +5V/1.5A, ±12V/250mA
- Attractive Wooden enclosures of Light weight Australian Pine Wood.
- User's Manual with 25 sample experimental programs.
Optional Interfaces :
- Code EET2481e - Interface Traffic Light for 43540, 43545
- Code EET2481f - Interface Stepper Motor for 43540, 43545
- Code EET2481g -Interface Real Time Clock for 43540, 43545
- Code EET2481h -Interface ADC0809 for 43540, 43545
- Code EET2481i-Interface Dual DAC0800 for 43540, 43545
8085 Micrprocessor Trainer
Code:EET2486
Specifications:
- High performance 8085A CPU @ 3 MHz
- 16 K powerful monitors FIRMWARE. Including all standard commands, codes, functions and utility subroutines besides Assembler and dissembler. 4K has been used for system firmware
- 8 K user RAM 6264
- Three 28 pin sockets provided for memory expansion up to a maximum of 56 K
- Versatile Keyboard/Display controller using 8279 brought out on separate FRC connector
- 46 parallel I/O lines, 22 from 8155 and 24 from 8255
- Serial I/O through auto adjusting type RS-232 channel. This connector is conveniently brought on the rear using SID-SOD lines
- Hex pad/Display Interface : 8279 Keyboard Display controller is used for Hex pad keys & Displays (6 Nos. of 7 segment Displays)
- Three 16 bit Timer/Counter channels are available on-board 8253. These channels are available on a 10 pin FRC connector
- On board 81C55-5 has a 2k-bit static RAM (256 bytes) with parallel I/O ports and a timer
- In built Assembler when connected with PC
- All address, data and control and hardware interrupt lines are brought out on a Pin FRC connector for system interfacing and expansion. All Study Cards are supported by this trainer kit
- RAM sockets are provided with battery back up using 3.6V Ni-Cad battery
- External Power Supply +5v 3Amp, +12v 1Amp, -12v 0.5Amp
- Supplied in attractive wooden enclosure
- Built-in audio cassette interface
8085 Microprocessor Trainer (LCD)
Code:EET2491
Specifications:
- High performance 8085A CPU @ 3 MHz
- On board 40x2 LCD display
- Operates on 5V,@1Amp. Optical built in or external power supply
- 16 K powerful monitors FIRM WARE .Including all standard commands, codes, functions and utility subroutines with Assembler and dissembler.4K has been used for system firmware
- 8 K user RAM 6264
- Three 28 pin sockets provided for memory expansion up to a maximum of 56 K
- Versatile Keyboard/Display controller using 8279 brought out on separate FRC connector
- 46 parallel I/O lines, 22 from 8155 and 24 from 8255 are brought out on separate FRC connector
- Serial I/O through auto adjusting type RS-232 channel. This connector is conveniently brought on the rear using SID-SOD lines
- On board AT connector for 104 Key standards PC-compatible keyboard
- Three 16 bit Timer/Counter channels are available on-board, using 8253.These channels are available on a 10 pin FRC connector
- All address, data and control and hardware interrupt lines are brought out on a Pin FRC connector for system interfacing and expansion. All Study Cards are supported by this trainer kit
- RAM sockets are provided with battery back up using 3.6V Ni-Cad battery
- On board PIO power supply connector is provided for PIO interface
- External Power Supply +5v 3Amp, +12v 1Amp, -12v 0.5Amp
- Supplied in attractive Metal enclosure R' L
8085 Microprocessor Trainer (LCD, USB)
Code:EET2496
Specifications:
- High performance 8085A CPU @ 3 MHz
- On board 40 X 2 LCD display, with optional 16 X 2 or 16 X 4 instead of 40 X 2 LCD
- Operates on 5V,@1Amp. external power supply On Boards 5v Adapter Jack
- 16 K powerful monitor FIRMWARE. Including all standard commands, codes, functions and utility subroutines with Assembler and dissembler. 4K has been used for system firmware
- 32 K user RAM 62256
- Three 28 pin sockets provided for memory expansion up to a maximum of 56 K
- Versatile Keyboard / Display controller using 8279 brought out on separate FRC connector
- 46 parallel I/O lines, 22 from 8155 and 24 from 8255 are brought out on separate FRC connector
- On Board USB interface hardware
- Serial I/O through auto adjusting type RS-232 channel. This connector is conveniently brought on the rear using SID-SOD lines or Jumper selectable USB connector
- On board PS2 connector for 104 Key standard PC-compatible keyboard
- Three 16 bit Timer / Counter channels are available on-board, using 8253.These Channels are available on a 10 pin FRC connector
- All address, data and control and hardware interrupt lines are brought out on a 50 pin FRC connector for system interfacing and expansion. All Study Cards are supported by this trainer kit
- RAM sockets are provided with battery back up using 3.6V Ni-Cad battery
- On board power supply screw terminal is provided for PIO interface
- External Power Supply +5v 3Amp, +12v 1Amp, -12v 0.5Amp
- Supplied in attractive wooden enclosure
High Performance 8085 Microprocessor Trainer
Code:EET2501
Specifications:
- High performance 8085A CPU @ 3 MHz
- 16 K powerful monitors FIRMWARE expandable to 32K
- 64 K user RAM with battery back up using 3.6V Ni-Cad battery
- Expanded RAM accessible using bank switching technique
- Write protect facility for RAM 6. Versatile Keyboard/Display controller using 8279 24 highly reliable dual function keys.
- digit seven segment LED display
- 48 parallel I/O lines available through two 8255 chips
- Serial I/O through 82C51A-2 USART, with on-board level shifters 1488, 1489. Programmable communication parameters
- Built-in audio cassette interface
- 3 channels of 16 bit timer/counters from 8253
- Powerful 8085 interrupt capabilities
- On-board EPROM programmer with ZIP socket for programming 2716 to 27512 EPROM's and various EPROM's
- Normal and intelligent programming modes
- On board ADC, DAC, opto-isolator, reed relay and miniature speaker
- On-board logic probe
- Single stepping, break pointing and machine cycle single stepping facility
- Monitor functions can be called through software interrupts
- Large collection of application software provided
- All address, data and control and hardware interrupt lines are brought out on a 50 pin FRC connector for system interfacing and expansion. All Study Cards are supported by this trainer kit
- External Power Supply +5v 3Amp, +12v 1Amp, -12v 0.5Amp(SMPS-03)
- Supplied in attractive wooden enclosure
Z80A Based Microprocessor Trainer
Code:EET2506
Specifications:
- High Performance Z80A CPU @ 4 MHz
- 8 K Powerful Monitor FIRMWARE in 2764 Includes all standard Commands, Codes, Functions & Utility subroutines
- 8 K user RAM
- Memory expansion capability up to 40 K
- Versatile Keyboard/Display controller using 8279
- 48 Parallel I/O lines from two 8255 chips
- Serial I/O through RS232 channel
- Built-in audio cassette interface
- 4 programmable counter timer channels from Z 80 CTC
- Powerful Z80A interrupt capabilities
- On-board EPROM programmer with ZIF socket for 2716 to 27512 EPROMs
- 6 digit seven segment LED display
- Highly reliable multi-function keypad with 24 keys
- All address data and control lines buffered and brought out on 50 pin FRC connector
- Supplied in a strong and attractive lightweight wooden case
- Power supply : Specially designed 230 V AC Power supply
8086 Microprocessor Trainer
Code:EET2511
Specifications:
- CPU is Based on 16 bit Intel 8086 High Performance CPU Operating at 8 MHz
- An Optiocal socket is provided for 8087-2 NDP (co-processor)
- 8284 clock generator & 8288 bus controller
- Powerful Monitor Firmware in two 27256 EPROMs (64KB) organized as 16 bit words. Monitor EPROMs expandable to 128 KB using two 27512 EPROMs
- 64 KB Static RAM in two 62256 RAMs organized as 16 bit words with battery back-up for data retention.
- 3.6 V Ni-Cad battery back-up circuit for static RAMs
- Hex pad/Display Interface through 8279 Keyboard Display controller
- On board 8254 Time/Counter chip. Out of 3 Channels of Timer/Counter Two Channels are totally available to the user through a 7 pin relimate Connector
- 48 TTL I/O Lines using two 8255 PPI chips and All Signals Terminated on Two26 pin FRC Connectors
- Printer Interface Provided through another 26 pin FRC Connector
- Interface: RS232 Port is provided for Serial Interface. 8251 USART along with 1488, 1489 driver Chip Provides Necessary signals brought out on a 9 bit D type Connector
- Baud Rates from 300 to 9600 can be selected through Software
- Interrupt Controller: The 8259 Interrupt Controller Provides 8 Prioritized interrupt Levels
- Detachable Hex Keypad & Display PCB
- All 8086 bus Signals terminated on 50 and 20 Pin FRC Connector
- Peripheral study cards can be Interfaced through 50 Pin FRC bus
- PIO Cards can be Interfaced through 26 Pin FRC connector Two Modes of Operation.
Modes of Operation:
- Monitor Mode : User Interaction through 28 Key Hex keypad and 8 Digit seven segment displays
- Serial Mode : Serial mode Through RS-232 Serial Port for Use with a Terminal
- Attractive Lightweight wooden enclosure
- Switch Mode Power Supply +5v 3Amp, +12v 1Amp, -12v 0.5Amp M 7 USER'S ANUAL 43 06
8086 Microprocessor Trainer (LCD, USB)
Code:EET2516
Specifications:
- CPU is Based on Intel 8086 High Performance CPU Operating at 8 MHz Speed
- Numeric Co-Processor : An Optional socket is provided for 8087-2 NDP
- 8284 A Clock Generator
- 8288A bus Controller
- Memory: 64 KB Powerful monitor firmware, expandable up to 128KB
- 64KB Static RAM with 3.6 V NI-cad battery backup
- 40 characters X 2 lines LCD Display
- IBM Compatible ASCII Keyboard
- On-board 8254 time/counter chip
- Printer Interface Provided Through another 26 Pin FRC Connectors
- RS232 compatible serial port using 8251, signals Terminated on 9 pin D-Type male connector
- On board 8259 PIC
- On board USB connector
- All address, data and control and hardware interrupt lines are brought out on a 50 pin FRC connector for system interfacing and expansion. All Study Cards are supported by this trainer kit
- Assembly language environment with inbuilt assembler & dis-assembler
- Terminal emulation software included
- Attractive wooden enclosure and operational manuals
- Switch Mode Power Supply +5v 3Amp, +12v 1Amp, -12v 0.5Amp
8086 Microprocessor Trainer (LCD)
Code:EET2521
Specifications:
- CPU is Based on Intel 8086 High Performance CPU operating at 8 MHz Speed
- Numeric Co-Processor : An optional socket is provided for 8087-2 NDP
- 8284 A Clock Generator
- 8288A bus Controller
- Memory: 64 KB Powerful monitor firmware, expandable up to 128KB
- 64KB Static RAM with 3.6 V NI-cad battery backup
- 40 characters x 2 lines LCD Display
- IBM Compatible ASCII Keyboard
- On-board 8254 time/counter chip
- Printer Interface Provided Through another 26 Pin FRC Connectors
- RS232 compatible serial port using 8251, signals Terminated on 9 pin D-Type male connector
- On Board 8259 PIC
- All address, data and control and hardware interrupt lines are brought out on a 50 pin FRC connector for system interfacing and expansion. All Study Cards are supported by this trainer kit
- Assembly language environment with inbuilt assembler & dis-assembler
- Terminal emulation software included
- Attractive Metallic enclosure and Operational Manuals
- Inbuilt Specially Designed 230v AC Input switch Mode Power Supply U 4 USER'S MAN AL - 3708
68000 Microcontroller Trainer
Code:EET2526
Specifications:
- MC68000 CPU operating at 8 MHz
- 32 K EPROM with Monitor FIRMWARE -'tutor'
- EPROM expansion possible upto 64 K maximum
- 16 K Static RAM with Ni-Cad battery back up
- RAM expansion possible upto 128 K maximum
- On-board EPROM programmer, with 28 pin ZIF socket for 2716 to 27512
- Standard / Intelligent / Programming modes
- Two RS232 channels with jumper selectable rates from 75 to 192000 Can be. interfaced to EXORciser or EXOR mac systems
- Five 8 bit parallel ports, 3 from 8255, 2 from 6821 available to user when EPROM programmer is not in use
- 68230 PI/T is used to provide a 8/16 bit parallel interface and a 24-bit timer. It is also used to provide a Centronics parallel printer port
- On-board single line assembler and disassembler
- Optional Macro Cross Assembler available for use on IBM compatible PC, to assemble and download user programs
- MACSBUG / VERSABUG command subset for debug functions.
- System address, data bus brought out on a 50 pin FRC connector and control bus brought on a 26 pin FRC connector for expansion and inter facing
- Power Supply : Specially designed 230 V AC power supply
8051 Microcontroller Trainer
Code:EET2531
Specifications:
- 8bit 8031/8051 microcontroller @ 10MHz
- System Monitor ROM is 8K bytes
- System break point RAM 32K bytes
- User RAM 8k bytes supplied (6264); provision for up to 32Kbytes (62256)
- User ROM is 8Kbytes
- Onboard Battery Backup for the user RAM
- On Board Peripheral chips -8155 RAM. I/O Timer, 8255 Programmable Peripheral Interface, 8253 Programmable timer Counter, 8251 USART
- Port accessible to user
- Two 8 bit Parallel ports from 8155
- Three 8 bit Parallel Ports from 8255
- One 8 bit on-chip Parallel port P1
- One on-chip Serial Port of 8031
- All address, data control and 8031 port P1 and P3 lines brought out on a 50 pin FRC connector for system expansion
- Operates with a serial CRT Terminal or with IBM Compatible PC Having terminal emulation software
- Modes Of Operation:
- Interrogation mode: for Interactive dialog with the system
- Assembler mode: for Programming directly in assembly language
- Continuation mode: for Setting RAM contents
- Single step mode: for single stepping, break pointing and debugging
- User Programs can be Downloaded or Uploaded in Intel Hex Format from the PC
- Power Supply: Specially Designed 230V AC Power Supply
8031/51 Microprocessor Trainer (LCD)
Code:EET2536
Specifications:
- Intel 80C51 Microcontroller Operating at 12MHz
- 32KB on board Program Memory
- 12KB Battery backed up user Program Memory
- 16KB Battery backed up User Data Memory
- 40 characters x 2 Lines LCD Display
- IBM Compatible ASCII Keyboard
- 8253 Timer/counter chip. Two Channels available to user
- 48 TTL I/O Lines using two 8255 PPI chips and all signal terminated on two 26 pin FRC (PIO card compatible) 9. RS232 compatible Serial port using 8250, signals terminated on
- pin D-type connector
- Study card support on 50 pin FRC connector
- Inbuilt specially designed 230v AC input Switch mode power supply
- Powerful monitor software with standard commands like move, fill, display/modify memory/registers, execute program, upload / download etc
- Single line assembler / dis-assembler
- Serial mode for using the kit with terminal
- Attractive Metallic enclosure and Operational Manuals
8031/51 Microprocessor Trainer (LCD, USB)
Code:EET2541
Specifications:
- Intel 80C51 Microcontroller Operating at 12MHz
- 32KB Onboard Program Memory
- 12KB Battery backed up user Program
- 16KB Battery backed up User Data Memory
- 40 characters x 2 Lines LCD Display
- IBM Compatible ASCII Keyboard
- 8253 Timer/counter chip. Two Channels available to user
- 48 TTL I/O Lines using two 8255 PPI chips and all signal terminated on two 26 pin FRC (PIO card compatible)
- RS232 compatible Serial port using 8250, signals terminated on 9 pin D-type connector On board USB connector
- Study card support on 50 pin FRC connector
- Powerful monitor software with standard commands like move, fill, display/modify memory/registers, execute program, upload / download etc
- Single line assembler / dis-assembler
- Serial mode for using the kit with terminal
- Attractive wooden enclosure and Operational Manuals
- External power supply SMPS-03
Science Lab Supplies Division of Narang Medical
